Is My Barbecue Ready Yet? – Cooking Beef Brisket

Join the forum discussion on this post - (3) Posts

By Kevin Bevington
Now that we have our rub, the right equipment, and we are able to control a consistent temperature, we are ready to attempt the toughest meat to cook, Beef Brisket. Lets first discuss how to select the meat you are about to cook. Beef Brisket can typically be sold in 3 different size cuts.

First, is the whole packer cut, this whole cut includes the 2 very distinctly different muscles that make up the entire cut, you have the flat which would be considered the flat long piece of meat, the point, which includes the nose end, and the meat layer underneath the flat, which is separated by a layer of fat which is also known as a deckle layer. The whole packer cut is the most desirable cut to cook in your smoker, the main reason being, the tremendous amount of fat that can be left on this cut to give it plenty of moisture to draw from while cooking.

The next cut would be just the flat cut. The flat is exactly that, if you buy this piece of meat, it will likely be closely trimmed, and that makes it more of a challenge to cook in your smoker, without drying it out.

Ok, now lets discuss the grade of meat you will need to choose, I will only touch on this briefly, because this subject could easily be an article of its own. The 3 beef grades we will discuss here are as follows;

Select - This grade is a leaner animal, and with beef brisket you need marbled fat to help get this fibrous cut tender, without falling apart, and being dry. This is not the grade to choose.
Choice - There is actually more than 1 level of choice, however, as a whole, choice has more marbled fat, and would be the one to pick, based on availability. You can cook a choice brisket until it is tender, without it falling apart, and without it being dry.
Prime - This grade has the highest level of marbled fat, and as a result, if cooked properly can produce a brisket of extreme quality. However, it can be very difficult to find.
Based on what is available to you, you need to select your brisket based on marbling (a web like appearance) of fat, and size. I would normally choose a heavier whole packer brisket, my favorite size somewhere between 14 and 16lbs. I would not cook one under 10lbs.

Now that we have our meat selected, you will want to marinate this piece of meat, either using a dry rub, or a combination of a marinade and a dry rub. You can also inject this piece of meat, however because it is so fibrous you will have to be very careful injecting, the majority of your injection could end up everywhere, instead of inside the brisket. If you do decide to inject, I would inject in the same direction as the grain.

Once you have placed your desired rub, and or marinade on your brisket, let this piece of meat marinate for at least 6 to 8 hours. I prefer to give it 10 to 12 hours marinate time.

Here is my recommended method for cooking this piece of meat. Your cooking temperature should be between 225 to 250 degrees F. Place the brisket in your smoker, fat side down, and cook until it the bark reaches the desired color. The internal temp at this point should be between 150 - 170 degrees F. Double wrap in aluminum foil, and put it back into your smoker, and continue to cook until tender in the thickest part of the flat. Using your instant read thermometer, the internal temp should be between 190 - 196 degrees F, and your thermometer should slide easily in and out of the meat. Then remove from your smoker, and let rest in a warmed environment, for a minimum of 1 hour. Then remove the brisket from the foil and slice against the grain, to a thickness of 3/8 of an inch. Serve immediately with your favorite bbq sauce.

Basic Brisket Rub

All BBQ Needs Is A Good Rub!

Join the forum discussion on this post - (1) Posts

By Kevin Bevington

As the masses begin to uncover their bbq grills and smokers for the season of barbecue and Grilling, many wonder what will set theirs apart from the rest. The answer? A good rub can make a world of difference. Sure, a good barbecue sauce is still a good thing to have to compliment your meal, but the seasoning is the key.

A bbq rub, is commonly referred to as a dry marinade, many times, it can actually bring more flavor to your barbecue than a liquid marinade, especially when used in a similar fashion.

Ok, lets look at the ingredient make-up of the barbecue dry rub, first, almost all barbecue rubs will contain the following basic ingredients;

Kosher Salt
White Sugar
Black Pepper
Paprika

These ingredients are typically used in fairly equal amounts, and other spices, and sugars can be thrown in to enhance flavor based on the type of meat you are cooking. A few of these additional ingredients are;

Spices
Celery Salt
Cumin
Chili powder
Cayenne Pepper
Garlic

Sugars
Brown Sugar
Turbinado Sugar
Demerara Sugar
Golden Granulated

The most important thing to remember about putting a good dry rub together is balance. A good balance of flavors is key to complimenting the meats natural flavor, you don’t want to cover it up.

Once we have our ingredients established, along with their measurements, we can now use them on our bbq. On thicker cuts of meat, such as pork shoulder cuts (used in pulled pork bbq), or beef brisket (a texas bbq favorite), we will want to give ample marinate time for the flavors to work into the meat. On these thicker cuts, you will want at least 4 to 6 hours at a minimum, but ideally 10 to 12 hours is best. On thinner cuts such as pork ribs, or steaks, you should be looking for a minimum of 30 minutes to 1 hour, and ideally 4 to 6 hours.

Another key to using a rub is to work the rub into the meat. When you apply a bbq rub, you can apply it over a wet base, such as mustard, or oil (olive or canola). This is called a wet rub application, and can help the rub adhere to the surface of the meat. The most popular way to apply a rub is to shake it on heavy and dry. Once this is done, it is important to work it in, or massage it into the meat. This will help the rub flavor penetrate much quicker.

Now that I have given you the basics, it’s your turn! But, I will give a great all purpose BBQ Rub that works especially well on pork, and chicken. Enjoy!

Basic BBQ Rub
1/4 cup brown sugar
1/2 cup turbinado sugar
1/2 cup paprika
1/3 cup garlic salt
1/4 cup kosher salt
1 tablespoon chili powder
1 teaspoon cayenne pepper
1 teaspoon ground cumin
1 teaspoon black pepper

Kevin Bevington is the Pit master of the Championship BBQ Team, HomeBBQ.com. He has won over 50 Championship Titles. He also sells some of the finest bbq and grilling rubs, and Barbecue Sauce. For more information, please visit:
http://shop.homebbq.com
http://www.homebbq.com